The Deltron BC system consists of high opacity solid, metallic and Pearl / mica colours. Deltron BC is designed for the repair of vehicles originally finished in a basecoat / clearcoat system. Used in conjunction with a recommended PPG repair system, Deltron BC meets or exceeds the performance requirements of motor manufacturer paint system warranties. As part of the Deltron Global Refinish System, Deltron BC carries a large number of OEM approvals.
Deltron Global Base Coat Tinters D7xx, D9xx, D9xxx
Deltron Thinners DT810, DT820, DT830, DT840
Deltron MS Hardener DH720
For matt, satin and textured finishes:
Deltron Texture Additive D843 to create a fine textured ‘suede’ effect
Deltron Leather Grain Additive D844 to create a coarser, more pronounced textured finish
Preparation of Substrate:
PPG 2K primers - P500 dry / P800 wet
Electrocoat - Preprime; Do not topcoat direct
Sound 2K finishes - P500 dry / P800 wet
TPA - P500 dry / P800 wet - Must be sealed (e.g. D834)
Before and after any sanding operation, the substrate must be thoroughly degreased using D845 or D837. Use D837 only, prior to painting.
Standard BC - BC 1 vol : Thinner 1 vol
Activated BC - BC 7 vol : DH720 1 vol : Thinner 8 vol
NOTE: DELTRON BC (Basecoat) activation may be necessary in cases, such as high film builds (i.e. more than four coats), commercial vehicles, motorbikes, or wheel painting where a higher impact resistance is necessary. This applies to PPG Custom finishes within the Vibrance collection, such as Harlequin, Radiance ll Candy, Prizmatique and 3-layer finishes.
Choose Thinner according to application temperature and repair area size:
|Up to 18'C||DT810|
|18'C - 25'C||DT820|
For exceptional conditions of temperature and humidity (>35'C or >70%) Extra Slow Thinner DT840 may be used in BC
Uncatalysed (no hardener): No Limit
Catalysed (with hardener): 6 hours
Spray Viscosity: 15 secs DIN4 at 20'C
Spray Gun Setup: 1.3 - 1.4mm
|HVLP / RP||Conventional|
|1.3 -1.8 bar / 20 - 25 PSI||1.8 - 2.5 bar / 25 - 35 PSI|
Number of Coats: 2-3 medium wet coats (+1 light control coat for metallics if required)
Flash Off at 25'C
Between Coats: 5-10 minutes
Before Clearcoat: 15 minutes
Drying Times at 20'C
Tape Time Standard BC: 15 minutes
Tape Time Activated BC: 30 minutes
Total Dry Film Build:
Theoretical Coverage*: 3.5 - 7m²/L ready-to-spray
*Assuming 100% transfer efficiency and dry film thickness as indicated
BC Colour - Refer PPG MSDS
DH Hardeners & DT Thinners - Refer PPG MSDS
Grade damp - To remove minor defects in Deltron BC, de-nib after 20 minutes flash-off using fine sand paper (P800 - P1200 or P1000 Abralon damp) followed by more base coat prior to the clearcoat application. Use damp fine sandpaper only and avoid using excessive water when de-nibbing.
Note: Do not wet sand large areas of Deltron BC basecoat. Wet sanding can lead to excessive water absorption by the basecoat and can downgrade the mechanical properties of the system particularly in the subsequent topcoats.
Activated - 15 minutes minimum prior to clearcoat application
Unactivated - 12 hours maximum prior to clearcoat application
After 12 hours Deltron BC has to be re-applied prior to clearcoat application
Overcoat with: Any approved PPG Global clearcoat
Shipping & Delivery
Orders will be shipped by couriers. Orders received before 1pm will be sent out same day.
If there are items missing we will send what we have with a note of when the rest of the order will be shipped or you will be offered a refund.
In some cases we ship from different locations, if this is the case you will be sent an email telling you of this.
We cannot ship out internationally outside of New Zealand.
Goods ordered which are either faulty or not as ordered may be returned for a full refund. This must be within a reasonable period.
This included goods which:
- are or become faulty through no fault of your own
- are not fit for a stated purpose or a purpose you made known to our sales staff
- don't match our description or sample (please note that some product pictures may not be of the actual product size - manufacturers supply us with a single product image to cover a range of package sizes - and that the size, volume or weight stated in the product description is what you will get)
- have defects that were not obvious or we did not bring to your attention.
Please ring us beforehand to get a Returned Merchandise number and instructions on how to return goods to ensure a speedy resolution.
IF YOU CHANGE YOUR MIND:
Sealed and undamaged items may be returned for a refund or account credit, but you will have to pay the shipping costs. Please ring our customer service centre (04-5866681) before sending anything back.
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.