PrimaGUARD is designed on the latest primer technology and can be used to optimise the priming process when used in combination with Deltron Basecoat. It is designed to deliver a high quality final appearance through a non sand process that is equivalent to a sanded primer. Excellent application, very smooth flow and superb holdout properties are at the core of this product’s performance
Due to the excellent adhesion characteristics of PrimaGUARD, no sanding of sound OE electrocoat is required, providing a very fast new panel painting process. PrimaGUARD can be coated with colour after flash off or left uncoated for up to 24 hours (at 20°C) with no sanding before topcoating with Deltron Basecoat. This allows new parts to be primed in batches in advance with minimal preparation ready for the topcoating process with the rest of the vehicle.
The strong adhesion and anti-corrosion characteristics mean that small rub throughs on electrocoated panels do not require the use of an etch primer before PrimaGUARD is applied.
Deltron PrimaGUARD DP621, DP625, DP627
Deltron Hardener DH710, DH720
Deltron Thinners DT860, DT830
Preparation of Substrate:
- Well cleaned unsanded Electrocoat
- Bare Steel, Galvanized Steel, Aluminium Up to 10cm diameter without the need for an Epoxy Primer
- Aged painted and original surfaces sanded with P320 or finer
- GRP, Fibreglass after final sanding with P320
- Polyester body filler after final sanding with P320
Note: For areas of bare metal above 10cm in diameter DP616 EpoxyTHANE may be used in standard mode or Wet-On-Wet prior to the application of PrimeGUARD. DO NOT apply PrimaGUARD over DP612 or any acid etch. DO NOT apply over SUA 1K Epoxy Primers unless COMPLETELY dry
Make sure all surfaces are de-greased, clean and dry before priming
Mixing Ratio % to achieve Greymatic Shades:
DP621 G1 (White) - DP625 G5 (Grey) and DP627 G7 (Dark Grey) can be mixed together to create G3 and G6 colours. Please follow the chart below to mix your choice of colour before adding hardener & thinner. DO NOT TINT WITH DG Tinters. This will cause adhesion issues.
Mixing Ratio by Volume:
|Deltron Hardener||1 volume|
|DT860 Primer Accelerator Thinner||0.5 volume Up to 30'C|
|DT830 Slow Thinner when overnight or batch priming||0.5 volume Over 30'C|
Potlife @ 20'C: 20 - 30 minutes at 20'C
Spray Viscosity @ 20'C: 16 - 18 seconds (DIN4)
Spraygun Setup: 1.3mm - 1.4mm
HVLP / RP 1.6 - 2 bar
Conventional 45-55 PSI / 160-200 KPA
Wet-On-Wet Application Guide:
PrimaGUARD should be filtered through a fine paint strainer and then applied in an even wet coat as if you were applying topcoat. Only one coat is required.
Note: PrimaGUARD can also be used for batch priming new parts. New parts pre primed with PrimaGUARD can be coated later without sanding for up to 24 hours(at 20°C). When spot priming, the use of SUA860 Blending Thinner will soften the blended edge of the primer.
If leaving overnight or batchpriming, DO NOT USE DP860. Panels should be topcoated within 24 hours.
Number of Coats & Flash Off:
Apply one even wet coat
Flash Off 15 minutes
Turn booth spray temperature up during flash off
Apply Deltron basecoat after flash off
If batch priming parts, leave to air dry overnight or bake at 65'C for 30 minutes
Total Dry Film Build: 25 - 35um
Batch Priming Only:
Overcoat / Recoat Prep: Degrease (De-Nibb if required)
Overcoat / Recoat Time: Up to 24 hours without sanding (at 20'C)
Shipping & Delivery
Orders will be shipped by couriers. Orders received before 1pm will be sent out same day.
If there are items missing we will send what we have with a note of when the rest of the order will be shipped or you will be offered a refund.
In some cases we ship from different locations, if this is the case you will be sent an email telling you of this.
We cannot ship out internationally outside of New Zealand.
Goods ordered which are either faulty or not as ordered may be returned for a full refund. This must be within a reasonable period.
This included goods which:
- are or become faulty through no fault of your own
- are not fit for a stated purpose or a purpose you made known to our sales staff
- don't match our description or sample (please note that some product pictures may not be of the actual product size - manufacturers supply us with a single product image to cover a range of package sizes - and that the size, volume or weight stated in the product description is what you will get)
- have defects that were not obvious or we did not bring to your attention.
Please ring us beforehand to get a Returned Merchandise number and instructions on how to return goods to ensure a speedy resolution.
IF YOU CHANGE YOUR MIND:
Sealed and undamaged items may be returned for a refund or account credit, but you will have to pay the shipping costs. Please ring our customer service centre (04-5866681) before sending anything back.
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.